Startseite|I/O-Analog
Category

I/O-Analog

P-2Rel4Di2Ai-##

2x Relay-Output, CO, potential free 4x Digital-Inputs, n-switch, 2-wire 2x Analog-Inputs, 10V/20mA, 2/3wire The Module includes two potential free relays, four digital inputs and 2 analog inputs with power supply. The digital inputs are designed for an external switch / open collector to ground. The analog inputs are either voltage or current inputs, depending on the variant. P-2Rel4Di2Ai-01 ID 5-131 module size 72mm x 66mm digital Input 4x com. ground ext. contact digital Output 2x Relay isolated CO analogue Input 2x 0..10V Notes Relay: 5A, 0..10V P-2Rel4Di2Ai-02 ID 5-132 module size 72mm x 66mm digital Input 4x com. ground ext. contact digital Output 2x Relay isolated CO analogue Input 2x 0/4..20mA Notes Relay: 5A, 0.. 20mA

P-2CcvCav4Do2Imp-01

2x Clack Control Valves with 2x Clack-Puls-Flow-Meter with 2x Resolver Inputs with 2x IR LED Outputs 1x Clack Alternator Valve 4x Digital Output (for driving LEDs) This module includes 3 motor controller with … Note: This module also requires the adaptor board inside the Clack-Filter- Valves. P-2CcvCav4Do2Imp-01 ID 5-601 module size 72mm x 66mm digital Input 4x 24Vdc (com. ground) analog Input 1x Conductivity other IOs  2x Clack Control (Valve head) 1x ClackAltern (Valve head) Notes supports: 2 softener control valve, 1 alternator valve 

P-LfTmpAoDAioImp-##

1x LF-Input, conductive, 2-wire 1x Temperature, KTY2K, 2-wire 1x Analog Output, 0-20mA, 2/3-wire 1x Analog Input, 10V/20mA,2/3-wire 1x Impuls-In-/Output, n/p-switch, 2/3-wire can be used also as a Digital-Input This module contains all IOs for a typical conductivity mesurement with a range of 1 ... 4000μS/cm (configurable). It supports the common cell constants of k = 0.01... 1.0 (configurable). An inte-grated temperature input (for KTY81, PT1000 on request) supplies the necessary temperature compensation. A special impulse input allows the direct adaption of a hall or reed-contact flow and volume sensor from 0.01 up to 250Hz. Addi-tionaly one universal analog input and one output can be used for other analog sensors/actors, both with a range of 0/4 … 20mA. Futhermore a semiconductor impulse output is present to control e.g. dosing ...

P-6Rel5DiPow-01

2x Relay-Output, NO, supply switching 2x Relay-Output, CO, supply switching 2x Relay-Output, CO, potential free 5x Digital-Inputs, 2-wire, common gnd 1x AC-Current Input,2/20 Ap The module includes 6 digital relay outputs, 5 n-switching inputs and 1 inductive AC-current senor. The module has two potential free change-over relays which can switch a continouse current of 4A. Four other relays are able to supply up to 230V. 2 of these are closing and the other 2 are switch-over. Each of the supplying relay can switch up to 5A. The max. permant sum current over the supply outputs is 5A. P-6Rel5DiPow-01 ID 5-302 module size 72mm x 110mm digital Input 5x ext. contact (com. ground) digital Output 2x  1Ph-NO (Relay 230V) 2x 1Ph-CO (Relay 230V) 2x CO (Relay isolated) Notes Meas: ...

P-112RelX-01

1x Relay-Output, NO, supply switching 1x Relay-Output, CO, supply switching 2x Relay-Output, NO, supply switching CAE_P-112RelPow-01: contains an additional AC-current measurement This module includes four relays with RC-Part and one independent current messurement. Relay 1 consists of a closing contact and can handle a permanent/pulse cur-rent of 5/16A. Relay 2 is a switchover contact and handles a perma-nent/pulse current of 5/8A. Relay 3 and 4 are closing contacts and handle a perma-nent/pulse current of 4/6A. The current messurement is developed up to 10A eff. P-112Rel-01 ID 5-101 module size 72mm x 66mm digital Output 3x 1Ph-NO (Relay 230V) 1x 1Ph-CO (Relay 230V) Notes Relay: 16/8/5A P-112RelPow-01 ID 5-102 module size 72mm x 66mm digital Output 3x 1Ph-NO (Relay 230V) 1x 1Ph-CO (Relay 230V) analog Input 1x ...

B-4DimLedI-##

4x LED-Dimmer, const. current, 12-40V This module contains four independent PWM-LED outputs with a common supply of 12...40V and a PWM-frequency of appox. 670 Hz. The PWM resolution is 24.000 steps. Each of these channels can control a permanent resistive load of max. 1A and contains a quick acting 1A melting fuse for output protection. B-4DimLedI-01 ID 4-565 module size 72mm x 55mm analogue Output LED-Dimmer-I  Notes 0...350mA, max. 40V  B-4DimLedI-02 ID 4-566 module size 72mm x 55mm analogue Output LED-Dimmer-I  Notes 0...700mA, max. 40V

B-4DimLedU-##

4x LED-Dimmer, PWM, 12-40V This module contains four independent PWM-LED outputs with a common supply of 12...40V and a PWM-frequency of appox. 670 Hz. The PWM resolution is 24.000 steps. Each of these channels can control a permanent resistive load of max. 2A and contains a quick acting 2,5A melting fuse for output protection. B-4DimLedU-01 ID 4-561 module size 72mm x 55mm analogue Output LED-Dimmer-UG Notes 0..100% PWM, max 40V/2A 

B-4Dim230T-##

4x 230V-Dimmer, phase angle, lead/trail This module contains four independent 230Vac dimmer outputs that includes a phase angle control with a resolution of 20.000 steps per half wave. To support inductive and capacitive loads, it is existing in 2 variants, for leading and trailing edge. Each of these channels can control a permanent resistive load of max. 400W and contains a quick acting 2,5A melting fuse for output protection. B-4Dim230T-01 ID 4-541 module size 72mm x 88mm analogue Output 230V-Dimmer Notes 230Vac, max. 2A, leading edge  B-4Dim230T-02 ID 4-541 module size 72mm x 88mm analogue Output 230V-Dimmer Notes 230Vac, max. 2A, trailing edge

B-8Temp-##

8x Temperature, KTY, 2-wire This module includes eight inputs for a temperature sensor with different ranges. It is typically used with a KTY with 2kOhm at 25°C. The module is equipped with enough clamps for the second con-nector of the sensor. B-8Temp-01 ID 4-401 module size 72mm x 44mm analogue Input 8 Temp-KTY2k  Notes KTY2k, -30...80°C  B-8Temp-02 ID 4-402 module size 72mm x 44mm analogue Input 8 Temp-KTY2k  Notes KTY2k, 5...45°C

G-5Ai3Imp-##

5x Analog-Input, 10V/20mA, 2/3-Wire 3x Impulse-Input, n/p-switch, 2/3-wire This module includes 5 analog inputs and 3 impulse inputs. The analog inputs are voltage or current inputs depending on the variant in use. The impulse inputs always measure the high time of the signal and frequencies up to 500Hz. G-5Ai3Imp-01 ID 2-451 module size 72mm x 44mm digital Input 3 ext. NPN / ext. contact analogue Input 5 0..10V Notes 0..10V; NPN-pulse  G-5Ai3Imp-02 ID 2-452 module size 72mm x 44mm digital Input 3 ext. PNP / ext. contact analogue Input 5 0..10V Notes 0..10V; PNP-pulse  G-5Ai3Imp-03 ID 2-453 module size 72mm x 44mm digital Input 3 ext. NPN / ext. contact analogue Input 5 0/4..20mA Notes 0.. 20mA; NPN-pulse G-5Ai3Imp-04 ID 2-454 module size 72mm x 44mm digital Input 3 ext. PNP / ext. contact analogue Input 0/4..20mA  Notes 0.. 20mA; ...

Nach oben